How much will it cost to put on a power steering belt pulley on my 1999 dodge intrepid?
Jun 23, 2010 by jacobcalhoun_66 | Posted in Maintenance & Repairs
i was driving, and heard a noise. i pulled over and the power steering belt pulley had broke off. i already bought the replacement. and i dropped it off at the auto shop. im just wondering what a average price would be for it to be installed?
its not alot depending that its only the pulley probably around 40$-60$
| Jun 23, 2010
What's hot
Hayden Automotive 5975 Idler and Belt Tensioner Pulley Automotive Parts and Accessories (Hayden, Inc.)
List Price: $25.40 Price: $6.47 You Save:$18.93 (75%)
List Price: $39.99 Price: $15.13 You Save:$24.86 (62%)
Crankcase pulley removal tool for most Honda and Acura engines
Designed with hardened chrome molybdenum steel construction
For removal and installation of crankcase pulley bolt
Dayco 89052 Belt Tensioner Pulley Automotive Parts and Accessories (Dayco)
Price: $10.25
Per Car Qty:1
Tensioner Pulley
ACDelco 38001 Belt Idler Pulley Automotive Parts and Accessories (ACDelco)
Price: $17.59
12-month/12,000-Mile Limited Warranty
Steel pulleys with high-quality bearings resist dirt and salt
ACDelco is an Original Equipment (OE) supplier and has the experience engineering and manufacturing components that achieve the highest quality standards required by vehicle manufacturers
Gates 38016 Belt Tensioner Pulley Automotive Parts and Accessories (Gates)
List Price: $29.99 Price: $12.99 You Save:$17.00 (57%)
BMW E36, E46, E39 Belt & Pulley Failure.
This video identifies why and when to replace serpentine belts, idler pulleys, and tension pulleys on BMW engines, the engine shown in this video ...
Belt and Pulley Basics
www.ericthecarguy.com www.bbbind.com Once again I team up with BBB Industries to bring you this video on what to look for with your belts and ...
How To Install Replace Belt Tensioner Pulley Ford Explorer Ranger Mountaineer 4.0L 93- ...
www.1aauto.com 1A Auto shows you how to repair, install, fix, change or replace a broken, noisy, squeaky, worn or groaning serpentine belt ...
How To Install Replace Serpentine Belt Idler Pulley Ford Taurus 3.0L V6 1AAuto. ...
www.1aauto.com 1A Auto shows you how to repair, install, fix, change or replace your worn out idler pulley on a 2001 Ford Taurus. This pulley is ...
belt pulley - Bookshelf
76 pages
Pulley and Belt Transmission
Creator: Rockwood Manufacturing Company | History - 2010-07
Publisher: Nabu Press
Coupled belt-pulley mechanics in serpentine belt drives
Creator: Lingyuan Kong | Belt drives - 2003
398 pages
Automotive Heating and Air Conditioning, Classroom Manaul/ Shop Manual
Creator: Mark Schnubel | Technology & Engineering - 2008-08-11
... Belt slipping Belt too loose Replace and/or tighten belt Clean pulleys and
... Repair as required and replace belt Pulley and/or bearing failure Repair ...
Publisher: Delmar Pub
2016 pages
Chilton's Auto Repair Manual 1993-1997
Creator: Chilton Book Company | Transportation - 1996-10
Crankshaft pulley 6. idler pulley 7. Water pump 8. Drive belt Drive belt routing
... Install the belt over the pulleys, making sure it is properly routed. ...
Publisher: Chilton Book Co
1232 pages
Moving the earth, the workbook of excavation
Creator: Herbert L. Nichols, David A. Day | Science - 2010-05-05
V pulleys have such high steep flanges that the belt cannot ... A belt drive may
slip because ofa slippery glaze on belt and pulley surfaces. ...
Timing Belt Pulley Nylon Glass Filled, Double Flange, 1/5" Pitch, 1/4" Bore, 1.082" Pitch Diameter: These 1/5 i...
< Spectre Performance 4388 Chrome Single >em/em< Crankshaft >em/em< for Small Block Chevy with Short Water Pump at Unbelievable Prices http://s
#Belt #Pulley Looking Timing Belt Pulley Here.Compare more product for you.Comparison
@ the pulley went bad and the belt that runs the car fell off
Noisy air con idler - I had my timing belt changed at the end of July and now the air con idler pulley is making a t...
astro start car starters Media
Checking for proper tightness for swamp cooler pulley belt
An up-close shot of a band saw I'm storing for a friend. ...one that's been too long unused. Gotta get back down to my basement/woodshop and start making sawdust again.